CISCO ASA 5585 X FIREWALL HOW TO
CISCO ASA 5585 X FIREWALL INSTALL
CISCO ASA 5585 X FIREWALL CODE

CISCO ASA 5585 X FIREWALL INSTALL

You must install the system ground before you attach the source DC power cables to the DC terminal block. The location of the system grounding pad is on the left-rear side of the ASA5585-X chassis ( Figure 3-1).Ĭaution The system ground serves as the primary safety ground for the ASA5585-X chassis that is equipped with DC-input power supplies. Step 4 Locate and remove the adhesive label from the system grounding pad on the back of the chassis. Step 3 Crimp the grounding wire in the barrel of the grounding lug and verify that the ground wire is securely attached to the ground lug. Step 2 Insert the stripped end of the grounding wire into the open end of the grounding lug. Step 1 Use a wire-stripping tool to remove approximately 0.75 inch (19 mm) of the covering from the end of the grounding wire. To attach the grounding lug and cable to the grounding pad, follow these steps: Crimping tool to crimp the grounding wire to the grounding lug.Wire-stripping tool to remove the insulation from the grounding wire.The length of the grounding wire depends on the proximity of the switch to proper grounding facilities (not supplied as part of the system grounding accessory kit). Commercially available 6 AWG wire is recommended.

Depending on the power supply and system, a 12 AWG to 6 AWG copper conductor is required for U.S.

Grounding wire-Should be sized according to local and national installation requirements.

Grounding screws-Two M4 x 8 mm pan-head screws (supplied as part of the system grounding accessory kit).

Grounding lug-A two-hole standard barrel lug that supports up to 6 AWG wire (supplied as part of the system grounding accessory kit).

To connect the system ground, you will need the following tools and materials: The equipment rack should also be connected to the CBN with 6 AWG grounding wire. A 6 AWG grounding wire is preferred from the chassis to the rack ground, or directly to the common bonding network (CBN).

CISCO ASA 5585 X FIREWALL CODE

Note In all situations, grounding practices must comply with Section 250 of the National Electric Code (NEC) requirements, or local laws and regulations. If you are installing the system ground on an ASA5585-X that is equipped with an AC-input power supplies, you do not need to power off the chassis. If the ASA5585-X is powered on, you must power it off before attaching the system ground.

For an ASA5585-X that is equipped with DC-input power supplies, you must install the system ground before you attach the source DC power cables to the DC terminal block.

You must connect both the system ground connection and the DC power-supply ground connection to an earth ground.

You must install the system ground connection with any other rack or system power ground connections that you make.

You must observe the following system-grounding guidelines for your chassis:

The system ground provides additional grounding for EMI shielding requirements and grounding for the low-voltage supplies (DC to DC converters). Note The system ground is also referred to as the network-equipment building system-ground.Ĭaution Installations that rely solely on system grounding using only an AC third-prong ground run a substantially greater risk of equipment problems and data corruption than those installations that use both the AC third-prong ground and a properly installed system ground.

CISCO ASA 5585 X FIREWALL HOW TO

This section describes how to connect the system ground to the ASA 5585-X, and contains the following sections: Connect interface cables to the ASA 5585-X, as described in Connecting Cables to the ASA 5585-X. Establish the system ground see the next section, Establishing the System Ground.Ĥ. Rack mounting instructions are provided in Installing and Removing a Slide-mounted Chassis.ģ. Place the ASA 5585-X on a flat, stable surface, or in a rack. Review the preparation directions and safety instructions in Preparing for Installation.Ģ. It contains the following sections:įollow this sequence when installing the ASA 5585-X:ġ. This chapter describes how to ground the chassis and install the cables.

Cisco asa 5585 x firewall